Pneumatic actuators are widely used in various valve control systems in industrial equipment, and their operational reliability is directly related to production safety and process stability. To ensure the long-term stable operation of the equipment, it is necessary to establish a standardized and systematic maintenance and management mechanism.

The prerequisite for all maintenance work is to ensure safety. Before any inspection or maintenance operation, the gas source should be turned off, residual gas in the cylinder should be emptied, and the power supply and control circuit should be cut off. It is strictly prohibited to work under pressure or with electricity to prevent misoperation and personal injury.
On this basis, the maintenance of pneumatic actuators should follow the basic principles of "maintaining cleanliness, checking seals, verifying actions, and stabilizing gas sources". For working environments with high dust, strong corrosiveness, or frequent movements, the maintenance cycle should be appropriately shortened and key area inspections should be strengthened.
routine inspection
Daily inspections are the first line of defense for discovering hidden dangers and preventing malfunctions. During the inspection process, the focus should be on checking whether the appearance of the actuator is intact, whether the fastening bolts are loose, and whether the piston rod has scratches, rust, and other phenomena; At the same time, confirm that there is no air leakage in the cylinder, pipe joints, solenoid valves, and other parts through methods such as listening to sound or soap water testing.
In the operation status check, it is necessary to observe whether the opening and closing actions of the actuator are smooth, whether there is any jamming or abnormal noise, whether the position is accurate, and whether there is no obvious deviation. In addition, it is also necessary to confirm that the Pressure of the air source is kept within the normal range of 0.4~0.7MPa, the filter is drained in time, and the signal feedback is consistent with the actual opening of the valve.
regular maintenance
On the basis of daily inspections, the executing agency also needs to carry out systematic maintenance on a periodic basis. Weekly or monthly maintenance mainly focuses on basic maintenance, including draining accumulated water from the filter, cleaning the surface of the actuator, and checking the oil level of the oil mist device and supplementing it with pneumatic special lubricating oil. The oil level is usually maintained at 1/3 to 2/3 of the volume.
Quarterly or annual maintenance belongs to the core maintenance content, and pneumatic special lubricating grease should be applied to the transmission parts; Calibrate the opening of actuators equipped with locators to ensure that the error is controlled within ± 1%; Simultaneously replace aging seals and O-rings. After maintenance is completed, continuous opening and closing of the actuator should be carried out 10-20 times throughout the entire stroke to verify the overall performance of the actuator, and the aging air pipe and filter element should be checked and replaced synchronously.
Key maintenance points for key components
In terms of the gas source system, the triple components of the gas source should be regularly drained, and the filter element should be cleaned or replaced in a timely manner when it becomes clogged; For oil-free lubrication systems, the oil mist device should be removed to avoid mistakenly adding lubricating oil.
Positioners and solenoid valves should focus on waterproof and dustproof measures to ensure firm and reliable wiring. It is recommended to calibrate the locator every six months. When the solenoid valve becomes stuck, the valve core can be disassembled and cleaned to restore sensitivity.
The cylinder and piston rod should be kept clean, and the surface of the piston rod can be coated with a thin layer of anti rust oil and equipped with a protective cover to prevent scratches and contamination. At the same time, it should be ensured that the actuator and valve maintain good coaxiality to avoid biased operation.
Common fault handling
When there is air leakage in the actuator, the gland or pipe joint can be tightened first. If the problem still exists, the seal or joint should be replaced directly. When stuck, prioritize cleaning and re lubricating the transmission parts. If there is no improvement, disassemble and inspect again.
When the opening of the actuator is not accurate, the locator should be recalibrated and the clearance between the connecting rods should be adjusted appropriately. If the actuator does not act, check whether the air source Pressure is normal, whether the solenoid valve is energized, and whether the air pipe is blocked.
Long term suspension management
Before the pneumatic actuator is stopped for a long time, it should be completely cut off from gas and power, and residual gas should be drained. The inlet should be sealed, and anti rust oil should be applied to the surface of the piston rod and flange, and a protective cover should be installed. During the shutdown period, the valve position should be fixed and manually turned once a month to complete full stroke opening and closing. The equipment should be stored in a dry, ventilated, and non corrosive environment.
In terms of spare parts and management, priority should be given to using original or same specification accessories, and lubrication products of different brands and models should not be mixed. At the same time, establishing a simple and clear maintenance ledger to record inspection, replacement, and calibration information can help with equipment status tracing and maintenance decision-making.